Expert Answers about Ford F-100, F-150, F-250, F-350
- Class V Trailer Hitch for 1973 Ford F-350 with 34 Inch Frame
- I checked with B&W and the Class V B&W Heavy-Duty Trailer Hitch # BWHDRH25122 is a confirmed fit for the 34 inch frame on your 1973 Ford F-350 that has a 10 inch step bumper.
The only thing you may need to do is remove or modify the spare tire carrier (if your truck has one) in order to ensure there is not interference with the hitch.
I have added a link to the installation instructions of this hitch for you to check out as well.
view full answer... - Class V Trailer Hitch for 1972 Ford F250 with Barden Bumper
- I am unfamiliar with the Barden Bumper and in my research, I could not find any specific information regarding the Barden Bumper. Our trailer hitches are not tested with aftermarket bumpers.
We have two bumpers that have been determined to be a fit for your truck with a factory bumper. The # BWHDRH25122 is for standard and step bumpers and the # BWHDRH25198 is for deep drop bumpers. I recommend measuring from your frame to the bottom of your bumper to know how much distance you will need...
view full answer... - Towing Mirror Fit for 1966 Ford F100
- The CIPA # 11902 you'd looked at would fit the mirror shown in the provided photo, which is found on 1999-2008 Ford Super Duty trucks as well as the 2000-2005 Ford Excursion. It wouldn't be a fit for the 1966 F-100, but we do offer mirrors that would work.
Because your existing mirrors are round, universal clip on mirrors wouldn't be a fit, but the CIPA # 11650-2 which actually attaches to the door via ratcheting straps would work. They aren't the best looking option in the world, but...
view full answer... - Ladder Rack for 1964 Ford F-250
- The Adarac Aluminum Series Custom Truck Bed Ladder Rack # A4001221 is a very nice system, though we simply sell them and do not actually produce them. They are custom-made to fit certain year, make and model of truck, and though unfortunately there are none which are going to fit your 1964 Ford F-250, but we do have an option for you.
The Yakima Outdoorsman 300 Ladder Rack # Y01137-Y00410 is a clamp-on installations that will work with your truck and provide you with a way to carry cargo....
view full answer... - Will Curt Hitch # C15300 Fit 1979 Ford F-150 Long Bed with Standard or Step Bumper
- Yes, the Curt Class V trailer hitch you referenced, part # C15300, is a confirmed fit for your 1979 Ford F-150 long bed with standard or step bumper and 37-1/2-inch wide frame. Installation will require some drilling and temporary removal of the spare tire. An install video is linked for you.
For a wiring harness you can use Draw-Tite # 18252 which provide a 4-pole flat trailer connector for your trailer lights.
A great option in a ball mount kit is item # EBMK2416 which includes a ball...
view full answer... - Recommended Replacement 14" x 14" Continuous Hinge Roof Vent Cover for 40 Year-Old Trailer
- From the picture that you sent in it looks like your vent cover has a continuous hinge. If that is the case then you just need to confirm that it measures 14" x 14".
If it does meet those requirements then the Replacement Lid for Elixir RV Roof Vent # CAM40156 will fit!
You could also use the metal Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent # BV0534-00 or the Smoke Replacement Lid for Ventline and Elixir RV Roof Vents # CAM40148 as well depending on what you are...
view full answer... - Recommended Pace Edwards Tonneau Cover With T-Slot Rails For A 1976 Ford F-150
- Pace Edwards doesn't have an UltraGroove that will fit your 1976 Ford F-150, but the Pace Edwards JackRabbit Retractable Hard Tonneau Cover w Explorer Rails # 311-JEF1290 will still give you the T-Slot rails that you were interested in.
These T-Slots will allow you to install a large variety of accessories including Thule or Yakima ladder racks, crossbars, Kayak carriers, bike racks, etc.
One of the most popular Kayak carriers we carry is the Thule Hullavator Pro Kayak Carrier and Lift...
view full answer... - Recommended Truck Bed Mat For A 1966 Ford F-100
- While we don't carry any custom-fit options for a 1966 Ford F-100 we do offer universal-fit options like the DeeZee Universal Utility Mat for Trucks and Trailers # DZ85005. DeeZee also offers a universal-fit tailgate liner # DZ86700 in a similar style to help protect your truck bed.
Both of these universal-fit mats can be trimmed to fit your bed and tailgate.
view full answer... - Where Does Draw-Tite Max-Frame Trailer Hitch Mount on 1966 Ford F-100 Frame
- The Draw-Tite Max-Frame Trailer Hitch # 75034 actually mounts to the underside of the 1966 Ford F-100 frame so since it looks like your gas tank is completely inside the frame you'll be able to mount the trailer hitch.
I took a trip out to the warehouse for a few different dimensions I thought you might like since it looks like you're doing some modifications. The crosstube of the trailer hitch sits roughly 2-3/4" below where it mounts to the frame and then the closest edge of the crosstube...
view full answer... - Availability of a Trailer Hitch For a 1966 Ford F-100
- We do have hitches available for your truck (see link) but none of them are designed to fit behind the tag (license plate). At this time I do not know of a Hidden or Stealth hitch that is available for your truck.
For a trailer hitch that would sit below the rear bumper, I recommend looking at the Draw-Tite Class III Trailer Hitch, # 75034. This hitch will fit as long as you have the standard or step bumper.
If you have a deep drop bumper, then you will want part # 41504.
view full answer... - Dimensions of Draw-Tite Max-Frame Trailer Hitch Receiver Part # 75034
- I do have some dimensions of the Draw-Tite Max-Frame Trailer Hitch Receiver part # 75034 which is a fit for a 1965 Ford F-100 and I have attached these for you below but I would not be able to provide a dimensional drawing as this is proprietary information that is not released by the manufacturer.
The distance from the frame to the top of the receiver tube opening is 5-5/8" which will allow you to determine how far under the rear bumper the receiver tube will sit. In regards to exhaust...
view full answer... - Will Access TonnoSport Fit a 1979 Ford F-100 Fleet Side Pickup
- The Access TonnoSport Soft, Roll-Up Tonneau Cover # A22010029 will fit the 6' Fleet side bed on your 1979 Ford F-100. I don't have the exact dimensions of this cover (all of the tonneau manufacturers just reply to that question with "it fits") but the "Standard Bed" we have listed in our fitguide is the Fleet side so you're good to go!
view full answer... - Replacement Regulator For Marshall Brass Co 240 Regulator
- The Camco Automatic Changeover part # CAM59005 will replace your marshall brass co model 240 without a problem. We do not carry the marshall brass co models but from what I could tell from my research they are just standard manual dual regulators. I was not able to find a BTU rating on the 240.
The Camco Automatic Changeover part # CAM59005 will automatically switch tanks for you when one is empty.
view full answer... - Brophy Clamp On Camper Tie-Downs Compatibility With A 1973 Ford F-250 Longbed
- If your 1973 Ford F-250 is not a dually and has bedrails that are not more than 5.5" wide and the space between the lip of the bedrail and the wall of the bedrail is at least 2" wide then the Brophy Clamp On Camper Tie-Downs # HSAB will work for your vehicle. These tie-downs will clamp onto the bedrails of your truck to provide you with attachment points for your truck bed camper. You'll also need some turnbuckles # TDHP to properly mount the camper to your tie-downs.
view full answer... - Will Curt Class IV Trailer Hitch Receiver Fit 1974 Ford F-250 with Standard Bumper and 34 Inch Frame
- The Curt # C14082 will fit on your 1974 Ford F-250 as long as you have the crew cab. It does bolt on but will require drilling into the frame to install.
I've attached a link that shows all of the Class IV hitch receivers confirmed to fit the different models of your F-250.
If you also need a wiring harness use the Hopkins # 40105 for a 4-way connector or the Draw-Tite # 20023 for a 7-way.
You might like an adjustable ball mount. The B&W Tow & Stow # BWTS10048B provides up to either...
view full answer... - Recommended Trailer Hitch Receiver For A 1982 Ford F-350 DRW With Deep Bumper
- Since your 1982 Ford F-350 DRW has the Deep Bumper I recommend the Curt 3-Piece Trailer Hitch Receiver - Multi Fit - Class V - 2" # C15511 as it will work with both 34" and 37-1/2" wide frames so you will not have an issue.
The # C15317 you were looking at is only confirmed to fit the 1988-2000 Chevrolet C/K series pickups with the 10" drop bumper and would not fit your F-350.
Keep in mind that while the # C15511 has a 1500lb tongue weight rating and 15000lbs trailer weight rating your...
view full answer... - Replacement Vent Lid for Older Heng's Vent Cover
- We do have one option we know will work as a replacement vent lid for a Heng's, which is a universal option from MaxxAir, and as you can see by the accompanying cut out, the hinge will attach right onto the frame of your vent. The MaxxAir UniMaxx is available in either smoke or white:
- Smoke: MaxxAir UniMaxx Universal Replacement Lid for RV and Trailer Roof Vent # MA00-335002
- White: MaxxAir UniMaxx Universal Replacement Lid for RV and Trailer Roof Vent # MA00-335001
I have added links...
view full answer... - Recommended Universal Truck Bed Mat for a 8 Foot Bed
- We have a universal mat that should fit the bed of your 1964 F-100 since you have the 8' bed. It is the DeeZee Universal Utility Mat for Trucks and Trailers Item # DZ85005. This bed mat is 8' long x 4' wide. This 3/8" thick rubber mat has a non-skid surface that prevents cargo from shifting.
I have linked a review video below so you can take a look at this mat being installed and used.
There are no custom fit options for a 1964 F-100.
view full answer... - Compatibility of the Tow Ready 4-Pole Mounting Bracket and the Curt T-Connector Wiring Harness
- Yes, the Tow Ready Mounting Harness # 18144 will wok with the Curt T-connector Harness, # C55301.
The mount can connect at the bumper of your vehicle to mount the 4-flat plug of the Curt harness.
view full answer... - Recommended White Spare Tire Cover for 29 Inch Tire
- When it comes to covers you really don't want to get something too small and try to make it work. It would be better to get something a little too large and have extra. Instead of getting a cover for a 28 inch spare tire I suggest the Camco Vinyl Spare Tire Cover # CAM45344 which is designed for 29 inch tires.
view full answer...
Go To Results